2803 Troy Road, Springfield Ohio

Cable Design

Designing your own Cable scheme

Battery cables

You won't likely be accomplishing this with a pair of scissors, so break out your sharpest blade, grinder, or precision cut-off saw and let's get to work!


Placing your Battery Bank

Consideration on arrangement of the battery bank in a manner that will facilitate all cuts to be as short and direct as possible, is a worthwhile priority.

Photo of a Deep Cycle Battery Bank with proper cabling

Unlike a 12volt Battery Bank, a 24v or 48v Battery Bank will require a bit more consideration and custom-cutting.

Deep Cycle Battery Bank with proper cabling

In a 12v Battery Bank, it is preferable to have the parallel negatives and positives connected in a solitary un-cut cable.

Deep Cycle Battery Bank with continous cabling

The cable seen above is not cut. It is simply stripped at the terminals to allow for the intermediary connections on the parallel negative or positive terminals.




If on a budget, A good set of fat jumper cables will be the least cost to accomplish the new cabling scheme. Cut off the clamps and cut to size.


Or


After having chopped the connectors specified in Tip #1, get a measurement leaving a slight allowance for movement on the parallel connections (none for the series connections).


Care should be taken while assessing your Battery Cable-cuts.

Photo of Deep Cycle Battery Bank


It's true, 12v electricity is eons safer than the grid electricity.

However mishandling batteries can hurt or kill you.

Photo of Battery Bank

Onward!




Create a template cut for your SERIES battery connections, and a template cut for your PARALLEL.


Less cuts on the parallel cables equates to less energy loss, and minimizes other potential detrimental variables.

These batteries are actually made by Dekka.

The argument for custom-cut cables isn't just an argument for safety's sake, or that it looks neater, or that the result are a more-efficient battery bank.


You are also gaining the least cost per lifetime by making your own cables.

Consider how many series connection wires you can obtain by simply cutting down the average automotive battery cable (3 for the price of 1 for me).


Off-Grid Use

The photo above shows two 48v Battery Banks, each comprised of eight 6v batteries. Although the orientation of the batteries is not optimal, the configuration allows for the wind turbine and solar inputs to be located at a central end. In the optimal orientation the 48v battery bank would be 8 batteries in a straight line. In the orientation seen in the photo above, notice that there is one series cable that is not congruent with the size of all the other series cables (seen near the purple Trojan batteries).


However when these 16 batteries were setup to comprise a massive 12v battery bank, the longest cable that could be located here was only long enough to span 3 of the 4 parallel batteries, then hopped to another eight 6v batteries (which were also connected in series to 12v).

In the 12v scenario, a stretch of cable was required to be doubled-up on the final terminal, and resume for yet another unadulterated stretch (just to hop over to the last remaining 12v battery).


The problem arises when the available cables are too short. If this happens to be the case for you, make absolutely certain to always keep the cuts to the back of the battery bank (away from the power-inputs and away from the power outputs or inverter connections).


This will be your weakest link.


In other words, the end that receives the solar or wind-generated power should be connected to the longest continuous stretch of cable at terminal 1, then through terminal 2, then (in my case) terminating at battery terminal 3 before adding another stretch of cable to the remaining batteries.


For instance, terminal 3 jumping to terminal 4 could become a hot-point if the energy coming into the battery bank is located at terminal 4 instead of terminal 1. Terminal 4 in this scenario is the end of the battery bank, which is where any deviation from an otherwise perfect battery cable-length ought to be placed.

By doing so diminishes any possibility of great heat building up due to the two opposing cable lengths having incurred shrinkage of wire, etc.


As a final note, if you see burned (odd-bright colors), blackened, or greasy wire, these are signs of damage and the cable should not be relied upon.

Find another purpose for the damaged cable.

Kenny's Solar

The reason you might find burned or blackened wire is due to overcharging, or a short-circuit, or some other problem, and a permanent remedy should be sought.


Click to the next page to read More about this Topic


Hello Springfield

2014-2022 Kenny Hendrick. All Rights Reserved. Visit a I-Love-America Moment

Back to Top